Industry information - Page 8 - Industrial purification heat recovery

Rotary/Wheel Energy Recovery Heat Exchanger

There are two types of rotary energy recovery heat exchangers:full heat type and sensible heat type.As a heat storage core,the fresh air passes through a semicircle of the wheel,while the exhaust air passes through another semicircle of the wheel,and the fresh air and exhaust air pass through the wheel alternately in this way.
in winter,the wheel regenerative body absorbs heat from the exhaust(wet),when moved to fresh air side,due to reasons of the poor temperature(wet),regenerative core body would release quantity of heat(wet),when to exhaust side,and continue to absorb the heat in exhaust quantity(wet).The energy recovery is achieved by such a repeated cycle,and the working principle is shown in the figure.During the summer cooling operation,the process is reversed.
When the full heat wheel runs,water molecules in the air are absorbed into the molecular sieve coating on the surface of the honeycomb,and when they are transferred to the other side,they are released due to the pressure difference between the water molecules.

The all-heat type runner USES the fresh air to exchange sensible heat and latent heat,so as to save energy and keep good ventilation in the room.The fresh air can be pre-cooled and dehumidified in summer and preheated and humidified in winter.

Air to Air Total Plate Heat Exchanger-BQC series

Structural characteristics of
·BQC type all-heat exchanger adopts cross countercurrent structure,with air partially cross flow and partially relative reverse flow.The new exhaust air is completely separated to avoid any transfer of odor and moisture;
·The all-heat exchanger USES ABS plastic frame,which is beautiful,has high strength,is not easy to be damaged,has a long service life,is environmentally friendly and has good sealing,which ensures the structural strength and tightness of the heat exchanger,and reduces the mixing of new exhaust air;
·The full heat exchange paper is made of imported non-porous film paper(ER paper)and processed by a special process.It is characterized by good air tightness,high heat transfer efficiency,tear resistance,aging resistance,corrosion resistance and antibacterial;
·All connections of the heat exchanger chip are sealed with sealant to ensure air tightness of the heat exchanger;
·It can be cleaned by vacuum cleaner and compressed air,easy to use and simple to maintain;
·Heat exchangers of various specifications and sizes can be developed according to user requirements.

Application and application mode
·AC Ventilation System
·Room Ventilation System
·Industrial Ventilation System
·Heat Pump Drying System
·Indirect Evaporative Cooling System
·Large-scale Scientific Breeding Bystem
·Purify Air Conditioning Fresh Air System
·Wind Generator Air to Air Indirect Cooling System
·Heat Recovery in Winter
·Cold Recovery in Summer

Air to Air Total Plate Heat Exchanger-BQB series

Structural characteristics of
·All-heat exchanger is formed by overlapping,bonding and processing of mutually perpendicular air channel corrugated and all-heat exchange paper.·The air passage for fresh air and exhaust air is a 90°vertical cross flow structure.The air passage is simple and smooth.
·There are two kinds of materials for the air channel to choose from.The A series adopts PVC,which is anti-aging,not easy to get dirt and breed bacteria and microbes.The spacing between the plates is 2.0mm~5.5mm.
·Series B adopts high-strength anticorrosive and flame-retardant corrugated paper with large contact area with heat transfer paper,which greatly improves the heat exchange efficiency.The plate spacing is available for choice of 2.0mm,3.0mm,4.0mm and 5.0mm.
·The full heat exchange paper is made of imported non-porous film paper(ER paper)and processed by a special process.It is characterized by good air tightness,high heat transfer efficiency,tear resistance,aging resistance,mildew resistance and antibacterial properties.
·Automatic production line is adopted to ensure the consistency of heat exchange sheet shape and surface flatness.·The size of the structure is not limited.Our company can process any square or rectangular section and any length of heat exchange core according to customer requirements.
·It can be cleaned by vacuum cleaner and compressed air,easy to use and easy to maintain.
application
·AC Ventilation System
·Room Ventilation System
·Industrial Ventilation System
·Heat Pump Drying System
·Indirect Evaporative Cooling System
·Large-scale Scientific Breeding Bystem
·Purify Air Conditioning Fresh Air System
·Wind Generator Air to Air Indirect Cooling System
·Heat Recovery in Winter
·Cold Recovery in Summer

Air to Air Total Plate Heat Exchanger-BQL series

Structural characteristics of
·The new exhaust air of BQL all-heat exchanger crosses and reversely flows at a certain Angle,with long flow passage,sufficient heat exchange and high heat exchange efficiency;·Diamond-shaped structure can effectively reduce the height of equipment and save installation space;
·The full heat exchange paper is made of imported non-porous film paper(ER paper)and processed by a special process.It is characterized by good air tightness,high heat transfer efficiency,tear resistance,aging resistance,corrosion resistance and antibacterial;
·Special adhesive coating process is adopted to ensure the air tightness of the heat exchanger and effectively avoid cross-contamination of new exhaust air;
·It can be cleaned by vacuum cleaner and compressed air,easy to use and easy to maintain;
·Different plate spacing(2.0mm,3.0mm,4.0mm,5.0mm)and any combination length;
·The structure size is not limited,and can be customized according to user requirements;

Application and application mode
·AC Ventilation System
·Room Ventilation System
·Industrial Ventilation System
·Heat Pump Drying System
·Indirect Evaporative Cooling System
·Large-scale Scientific Breeding Bystem
·Purify Air Conditioning Fresh Air System
·Wind Generator Air to Air Indirect Cooling System
·Heat Recovery in Winter
·Cold Recovery in Summer

Air to Air Sensible Plate Heat Exchanger-BXB series

Structural characteristics of
·BXB sensible heat exchanger can be made of seawater corrosion resistant hydrophilic aluminum plate,epoxy resin aluminum plate or stainless steel plate;
·The heat transfer surface of the heat exchanger was strengthened by heat transfer stamping,and the heat transfer area was increased by 10%-12%;
·The heat exchange sheet adopts enhanced punching and biting technology,with higher strength,better sealing,and air leakage rate less than 1%;
·The air passage is supported by a conductor convex cylinder with a high pressure difference capacity of 2500Pa for new exhaust;
·The normal service temperature of ordinary aluminum foil is not higher than 100℃;the temperature resistance of special sealing material can be up to 200℃;the temperature resistance of stainless steel can be 350℃;
·Tap water or neutral washing liquid can be used for direct cleaning,which is easy to use and easy to maintain;
·Different plate spacing(2.0mm-10.0mm)and any combination length can be provided.

application
·AC Ventilation System
·Room Ventilation System
·Industrial Ventilation System
·Heat Pump Drying System
·Indirect Evaporative Cooling System
·Large-scale Scientific Breeding Bystem
·Purify Air Conditioning Fresh Air System
·Wind Generator Air to Air Indirect Cooling System
·Heat Recovery in Winter
·Cold Recovery in Summer

Air to Air Sensible Heat Exchanger for Evaporative Cooling Air-Conditioning & Wind Power

Structural characteristics of
·BXB sensible heat exchanger can be made of seawater corrosion resistant hydrophilic aluminum plate,epoxy resin aluminum plate or stainless steel plate;
·The heat transfer surface of the heat exchanger was strengthened by heat transfer stamping,and the heat transfer area was increased by 10%-12%;
·The heat exchange sheet adopts enhanced punching and biting technology,with higher strength,better sealing,and air leakage rate less than 1%;
·The air passage is supported by a conductor convex cylinder with a high pressure difference capacity of 2500Pa for new exhaust;
·The normal service temperature of ordinary aluminum foil is not higher than 100℃;the temperature resistance of special sealing material can be up to 200℃;the temperature resistance of stainless steel can be 350℃;
·Tap water or neutral washing liquid can be used for direct cleaning,which is easy to use and easy to maintain;
·Different plate spacing(2.0mm-10.0mm)and any combination length can be provided.
Air to Air Sensible Heat Exchanger for Evaporative Cooling Air-Conditioning&Wind Power(图2)
application
·AC Ventilation System
·Room Ventilation System
·Industrial Ventilation System
·Heat Pump Drying System
·Indirect Evaporative Cooling System
·Large-scale Scientific Breeding Bystem
·Purify Air Conditioning Fresh Air System
·Wind Generator Air to Air Indirect Cooling System
·Heat Recovery in Winter
·Cold Recovery in Summer

air to air heat exchanger calculator

An air-to-air heat exchanger calculator typically helps in determining the heat transfer and energy recovery efficiency of an air-to-air heat exchanger or heat recovery ventilator(HRV)system.The exact calculations can be complex and depend on various factors,including the type of heat exchanger,temperature differences,flow rates,and specific heat capacities.To use such a calculator,you would typically need the following information:
1.Temperature Differences:You would input the incoming air temperature and the exhaust air temperature to calculate the temperature difference.
2.Flow Rates:The flow rates of the incoming and exhaust air streams are needed to determine the heat transfer rate.
3.Specific Heat Capacities:Specific heat capacities of the air on both the supply and exhaust sides are used in the calculations.
4.Efficiency:The calculator may also provide an efficiency rating,indicating how effectively heat is transferred from the outgoing air to the incoming air.
5.Heat Recovery:The calculator may show the amount of heat energy recovered,which can be valuable for estimating energy savings.
Specific calculators can vary in complexity,and there are both simple and more advanced tools available online or as software applications.For precise calculations,especially for complex systems,it's often recommended to use dedicated HVAC design software or consult with a professional HVAC engineer.
When using such a calculator,ensure that you have accurate input values to get meaningful results for your specific air-to-air heat exchanger system.

Air compressor filter element level

The filter element level of air compressor filters is usually in microns（ μ m) Represented in units, it is used to describe the size range within which filters can effectively remove particulate matter. Different applications require different levels of filters, which typically include:

Coarse filtration: usually at 25 μ M to 100 μ Within the range of m, it is mainly used to remove larger particulate matter, such as dust and particulate matter. This level of filter is usually used for pre filtration of air compressors to protect finer filters.

Precision filtration: usually at 1 μ M to 25 μ Within the range of m, it is used to remove smaller particles and solid particles. This level of filter is commonly used to provide cleaner air to meet specific application requirements, such as food processing and pharmaceuticals.

Ultra precision filtration: usually at 0.01 μ M to 1 μ Within the range of m, it is used to remove small particles, including bacteria, viruses, and small particles. This level of filter is typically used for high demand applications such as electronic manufacturing and healthcare.
The selection of an appropriate filter level depends on the application requirements, and usually needs to be based on the properties of smoke, particulate matter, and liquid droplets. In general, a coarse filter is used for pre filtration, followed by precision or ultra precision filters to ensure the required air quality and dryness are provided. Different applications may require different levels of filters to meet standards for cleanliness and particulate matter control.

Share Industrial purification heat recovery

In order to meet the needs of different customers in different occasions, Zibo Qiyu Air Conditioning Energy Saving Equipment Co., Ltd. has developed various forms of heat recovery system products, including heat pipe type, plate type, rotary wheel type, liquid circulation type and other heat exchangers, as well as new air exchangers developed by applying heat exchange technology, combined heat recovery air conditioning units, flue gas whiteners, industrial heat recovery boxes and other products, which are widely used in commercial central air conditioners, industrial purification air conditioners Healthy green residence, indirect evaporative cooling system of data center, heat dissipation of offshore wind power engine room, heat exchange of Charging station, medical and pharmaceutical purification, nmp waste heat recovery, large-scale breeding and energy-saving ventilation of fungus pig house and chicken house, heat recovery of printer coater setting machine, drying of food, tobacco sludge, wood, paper, medicine and leather, industrial flue gas whitening, mine exhaust heat recovery and other fields meet the needs of different customers. Welcome friends from all walks of life to guide and negotiate business!

Material and Application of Oil Mist Filter Element

Apologies for the mix-up. Here is the information on the materials and applications of oil mist filter cartridges in English:

Fiber material filter cartridge: Fiber materials such as glass fiber, synthetic fiber, or polyester fiber are commonly used in oil mist filter cartridges. These cartridges utilize the high surface area and fine pore structure of the fibers to effectively capture and filter oil mist particles from the air, improving indoor air quality and protecting equipment.

Activated carbon filter cartridge: Activated carbon filter cartridges are used in oil mist filters that require the removal of odors and harmful gases. Activated carbon has strong adsorption capabilities and can remove volatile organic compounds (VOCs), odors, and other pollutants from the air.

Electrostatic filter cartridge: Electrostatic filter cartridges are suitable for high-efficiency oil mist filters that contain internal electrodes. These cartridges utilize electrostatic forces to attract and separate oil mist particles. They can capture tiny oil mist particles and help maintain equipment cleanliness and operational efficiency.

High-efficiency filter cartridge: High-efficiency filter cartridges typically have a dense fiber structure and fine pores to filter out small oil mist particles and solid particles. They are widely used in environments that require high filtration efficiency, such as laboratories, medical equipment, and precision manufacturing.

Please note that the above information provides examples of common oil mist filter cartridge materials and applications. The actual selection should be based on specific application environments, filtration requirements, and equipment needs. It is recommended to refer to the product specifications and technical guidelines provided by the manufacturer and evaluate and select based on the actual circumstances.

Industrial purification heat recovery

Category Archive Industry information